? bubbles in syringe + injection sites

Discussion in 'Feline Health - (Welcome & Main Forum)' started by Steph & Quintus & L & O, Dec 23, 2017.

Thread Status:
Not open for further replies.
  1. Steph & Quintus & L & O

    Steph & Quintus & L & O Well-Known Member

    Joined:
    Dec 9, 2017
    When I draw the insulin (Lantus, from the pen) I always end up with a tiny bubble in the syringe. Before putting the syringe in the pen, I move the plunger back and forth a bit, and I press it in hard as I go into the pen. I suspect the micro-bubble is whatever residual air was in the syringe.

    I usually tap it, and expel the extra insulin, and hope that the bubble goes out with it.

    - how important is it to get rid of that teeny-tiny bubble?
    - how much extra insulin do you draw and then squirt out to get rid of the tiny bubble?

    I've read stuff about varying injection sites, particularly with Lantus. How important is that? I inject around the scruff but always in the same area (but I try to go a little to the side, a little higher, lower, etc.)
     
    Squalliesmom likes this.
  2. Phoebes (GA)

    Phoebes (GA) Well-Known Member

    Joined:
    Jan 16, 2017
    I always draw out a unit more then tap the needle to get all the bubbles to the top then twist the plunger to the dose. Usually by then I will see insulin expelled thru the bevel. And the bubbles are gone. I would say it's important to get most all the bubbles out because even a drop of insulin can be a "dose". But tiny, tiny bubbles I do not worry about.
    As far as sites I've been told to rotate. So I have about a 4x4 area on the right side of her flank that I work clockwise. Morning dose 12 oclock evening dose 3 o'clock then next morning 6 o'clock ect ect. Sometimes I forget what oclock I was on. Lol but then just start from 12. And don't rub after injection. I bend over to smell her if I think there was a fs. Of course with 17 units you can't miss that smell. Bending over or not.
     
  3. Tracey&Jones (GA)

    Tracey&Jones (GA) Well-Known Member

    Joined:
    Dec 12, 2016
    I do the same as Angela draw a bit more then I need, work the bubble to the top and and twist up gently to get the bubble and down to dose. I use exactly your technique but it seems with the BD you always get those little bubble.
     
  4. Squalliesmom

    Squalliesmom Well-Known Member

    Joined:
    Jun 26, 2015
    That's funny, the BD syringes are the only ones I don't have a bubble problem with, lol!:)
     
  5. Steph & Quintus & L & O

    Steph & Quintus & L & O Well-Known Member

    Joined:
    Dec 9, 2017
    how do you do it??
     
  6. Tracey&Jones (GA)

    Tracey&Jones (GA) Well-Known Member

    Joined:
    Dec 12, 2016
  7. Squalliesmom

    Squalliesmom Well-Known Member

    Joined:
    Jun 26, 2015
    I don't know what to tell you, lol. I'll go through the steps I use when filling syringes.

    I make sure the plunger is very tightly pressed when I insert the needle into the bottle, then just let it go, without pulling it back, for a second or two, and some insulin will start to fill the syringe. Then I pull it back and draw up a little bit more than I need, tap it so the bubbles all go to the top (I've found, with BD, you have to make sure the bubble(s) are centered in the top of the syringe), and, with it still pointing upwards, expel the extra insulin. Then I'll usually turn it upside-down to make sure I did, indeed, get all the bubbles out. If I didn't, I'll tap it again and get rid of the bubble, and add more insulin, if necessary. I almost never have a problem with the BDs, and very rarely have to go through the second part of the above explanation. *shrug* It works for me. I hope maybe it'll help you. :)
     
    Critter Mom and Kris & Teasel like this.
  8. Tracey&Jones (GA)

    Tracey&Jones (GA) Well-Known Member

    Joined:
    Dec 12, 2016
    Hmmm...maybe it is the wait of 1-2 seconds without pulling...just letting the syringe fill....
     
  9. Critter Mom

    Critter Mom Well-Known Member

    Joined:
    Jun 16, 2014
    This!


    Mogs
    .
     
    Squalliesmom likes this.
  10. JeffJ

    JeffJ Well-Known Member

    Joined:
    Jul 7, 2016
    There is almost always a bubble when I pull the insulin. The bubble is tiny so I just leave it. The way I figure - if the bubble is the same then it is part of the measured dose. I avoid wasting insulin by trying to get rid of it. Before the injection, I tap the syringe with the plunger facing up. So the bubble hugs the plunger, and basically gets stuck in the needle.
     
    Critter Mom likes this.
  11. Tracey&Jones (GA)

    Tracey&Jones (GA) Well-Known Member

    Joined:
    Dec 12, 2016
    I tried just waiting ...1 Mississippi, 2 Mississippi...and no bubble.
     
  12. rawia

    rawia Member

    Joined:
    Aug 24, 2017
    I used to have same issue until i found this good trick. First push the plunger to draw a drop dose ( there will be no air for drop dose) then draw little bit more and you will have no air for sure. After that adjust the units you need.
     
    Critter Mom likes this.
Thread Status:
Not open for further replies.

Share This Page